Skip to content
GeoEQ · Geotechnical software research lab · University of Utah

GeoEQ Seismic · Seismic site response

Seismic site response software for 1D and 2D analysis

GeoEQ Seismic is seismic site response software in development for one- and two-dimensional analysis of how layered ground modifies earthquake shaking.

GeoEQ Seismic In development 1D equivalent-linear first 2D in development

GeoEQ Seismic is not yet released. This page explains the method and the scope being built.

The basics

What is seismic site response analysis

Seismic site response analysis calculates how the soil and rock layers beneath a site modify earthquake ground motion between bedrock and the ground surface. It is also called ground response analysis, and its output is an estimate of surface shaking, response spectra and seismic site amplification.

Why surface shaking differs from rock shaking

Soft layers over stiffer ones trap waves and amplify motion near the site's natural period, while the same layers soften and dissipate energy as strain grows. Stiffness and damping both depend on strain, which is why a straight multiplication factor rarely captures the effect (Kramer, 1996).

Where it fits

A hazard analysis supplies motion on rock. Site response carries that motion up through the soil column to the surface. Liquefaction and foundation checks then use the surface motion; see liquefaction analysis software and foundation design software from the same lab.

Methods

Equivalent-linear site response analysis

One-dimensional site response assumes horizontal layers and vertically propagating shear (SH) waves. The equivalent-linear method, introduced in the SHAKE program (Schnabel, Lysmer and Seed, 1972), keeps the calculation linear in the frequency domain and handles nonlinearity by iteration.

  1. 01

    Start from small-strain stiffness

    Set each layer to its small-strain shear modulus Gmax and a low damping ratio.

  2. 02

    Solve the linear problem

    Propagate the input motion through the layers in the frequency domain with a transfer function.

  3. 03

    Find the effective strain

    Take the peak shear strain in each layer and scale it, commonly to about 65% of the peak, to represent the whole record.

  4. 04

    Update modulus and damping

    Read G/Gmax and damping at that strain from the curves, then repeat until the values stop changing within a tolerance.

Linear and equivalent-linear (frequency domain)

A linear analysis uses one modulus and one damping value per layer. The equivalent-linear method repeats it with values compatible with the strain the layer actually experiences. The effective strain is a fraction of the peak, often taken as (M - 1) / 10 for earthquake magnitude M (Idriss and Sun, 1992), which gives roughly 0.65 for M 7.5.

Because one value represents a whole record, equivalent-linear analysis can over-damp high frequencies at large strains. That is the reason comparison studies recommend checking whether it suits strong shaking (Kim et al., 2016).

Nonlinear time-domain analysis

Nonlinear analysis integrates the equation of motion step by step with a hysteretic soil model, so modulus and damping change within the record (Kwok et al., 2007). It is a separate method from the one above; GeoEQ Seismic does not list it in the scope described on this page.

Modulus reduction and damping curves

Curves give G/Gmax and damping ratio (in %) against shear strain (in %). They come from laboratory tests or published models such as Darendeli (2001). The same Vs profile with different curves gives different spectra, so the choice should be stated in the report.

Dimensions

1D vs 2D site response

One-dimensional

When horizontal layering is a good assumption

A 1D analysis treats each site as a single vertical column with horizontal, laterally uniform layers. It suits level ground away from basin edges and strong lateral contrast, and it is the standard approach in practice. It is the focus of the first release of GeoEQ Seismic, using the equivalent-linear method.

Two-dimensional

Basin edges, valleys and topography

Where the ground changes along a section, waves refract, reflect and travel sideways, and surface-wave energy can be generated at a basin edge (Bard and Bouchon, 1980). A 2D model represents that lateral variation, and it can be compared with a 1D column at the same location. Two-dimensional analysis in GeoEQ Seismic is in development.

Placing several 1D columns along a section gives 1D results at each point. It does not model lateral wave propagation, so it is not a 2D analysis. During development, results are being checked against established benchmark software.

Inputs

What a site response analysis needs

The scope of the first release of GeoEQ Seismic is built around these four inputs. Shear-wave velocity is never inferred from SPT blow counts unless a correlation is declared.

01Vs, thickness

Shear-wave velocity profile

Vs in m/s for each layer, with layer thickness in m. Vs sets the stiffness at small strain (Gmax = rho x Vs squared) and the travel time of waves through the column.

02Layer properties

Unit weight and soil type

Unit weight in kN/m3 gives mass density for every layer. Plasticity index, overconsolidation ratio and confining stress feed the curve models that need them.

03G/Gmax and D

Modulus reduction and damping curves

G/Gmax and damping ratio against shear strain, for example from the Darendeli (2001) model, which uses plasticity index, overconsolidation ratio and mean effective stress. Laboratory curves are preferred where tests exist.

04Outcrop or within

Input ground motion

An acceleration time history, for example a PEER NGA record in .AT2 format, declared as rock outcrop or within motion. The declaration decides how the base of the column is modelled.

Outputs

What it produces

Vs30 is computed as 30 m divided by the sum of layer thickness over Vs for the top 30 m. Each layer contributes its own shear-wave travel time, so soft layers weigh heavily in the result.

01PSA, 5% damping

Response spectra

Spectral acceleration at 5% damping for the input motion and the surface motion, so period-dependent change in shaking is visible directly.

02Surface / input

Amplification

The ratio of surface to input spectral acceleration, or the transfer function between the two, across period or frequency.

03PGA, strain, stress

Depth profiles

Peak acceleration, shear strain and shear stress with depth, plus the strain-compatible modulus and damping the iteration settled on.

04Computed value

Vs30 of the profile

The time-averaged shear-wave velocity of the top 30 m, computed from the Vs profile you entered. It is reported as a number; GeoEQ Seismic does not assign a site class from it.

How it is being built

Where GeoEQ Seismic is today

GeoEQ Seismic is in development. This is the scope being built, not a list of released features.

Scope of the first release

  • One-dimensional equivalent-linear analysis of layered ground
  • Modulus reduction and damping curves, with Darendeli (2001) as an example model
  • Recorded input motions in PEER .AT2 format, declared as outcrop or within
  • Response spectra, amplification, depth profiles and Vs30 of the profile

In development

  • Two-dimensional site response of layered ground, shown beside a 1D baseline
  • Traceable runs, with declared assumptions kept with the results
  • Working from the soil profile logged in GeoEQ SPT Logs
  • Checks against established benchmark software

For context

Other tools engineers use

Many programs already perform one-dimensional site response. This list summarises each program's published description and is not a ranking. Check each vendor's documentation for current capabilities.

One-dimensional site response programs and their published method coverage
ProgramDeveloped byPublished description
DEEPSOILUniversity of Illinois at Urbana-Champaign (Hashash et al.)One-dimensional site response in the time domain (nonlinear) and the frequency domain (equivalent-linear and linear).
StrataKottke and Rathje, PEEREquivalent-linear analysis with random vibration theory and randomisation of site properties.
SHAKE91 and SHAKE2000Idriss and Sun; GeoMotionsFrequency-domain equivalent-linear ground response, the lineage that began with SHAKE in 1972.
ProShakeEduPro Civil SystemsOne-dimensional equivalent-linear ground response analysis.
EERAExcel-integrated implementationEquivalent-linear ground response run from a spreadsheet environment.
RSSeismicRocscienceOne-dimensional nonlinear and equivalent-linear analysis.
SeismoSoilCaltechOne-dimensional linear, equivalent-linear and nonlinear analysis.

GeoEQ Seismic is aimed at the same one-dimensional equivalent-linear workflow, with two-dimensional analysis in development. For scripted geotechnical calculations, the open-source geoeq library for Python is a separate project.

Glossary

Key terms

Seismic site response analysis
Seismic site response analysis calculates how the soil and rock layers beneath a site modify earthquake ground motion between bedrock and the ground surface.
Equivalent-linear analysis
Equivalent-linear analysis approximates nonlinear soil behaviour by repeating a linear frequency-domain calculation with modulus and damping updated to be compatible with the computed shear strain.
Vs30
Vs30 is the time-averaged shear-wave velocity of the upper 30 m of a profile, equal to 30 m divided by the total shear-wave travel time through those 30 m.

Direct answers

Frequently asked questions

The same answers appear in structured data, so people, search engines and AI systems read one version.

What is seismic site response analysis?

Seismic site response analysis calculates how the soil and rock layers beneath a site modify earthquake motion between bedrock and the ground surface. It is also called ground response analysis. The result is an estimate of surface shaking, response spectra and amplification (Kramer, 1996).

What is the difference between equivalent-linear and nonlinear site response analysis?

Equivalent-linear analysis repeats a linear frequency-domain solution with strain-compatible modulus and damping (Schnabel, Lysmer and Seed, 1972), while nonlinear analysis steps a hysteretic soil model through time. Published comparisons find the two differ most at large strains and short periods (Kim et al., 2016).

When is nonlinear analysis preferred over equivalent-linear?

Nonlinear analysis is generally preferred for strong shaking and soft soils, where shear strains become large. There is no single universal threshold, so check the selection criteria in the literature and the requirements of the project.

How are modulus reduction and damping curves chosen?

Curves come from laboratory tests on the site soils where available, otherwise from published models. Darendeli (2001) is a widely used model based on plasticity index, overconsolidation ratio and mean effective stress. Curve choice changes the result materially, so it should be documented.

When is 2D site response needed instead of 1D?

Two-dimensional analysis is needed when the ground is not horizontally layered, for example at basin edges, in steep valleys and canyons, and under pronounced topography. There, waves travel sideways and a 1D column can under-predict shaking (Bard and Bouchon, 1980).

What is Vs30 and how does it relate to site response analysis?

Vs30 is the time-averaged shear-wave velocity of the top 30 m of the profile. Building codes use it to group sites into classes, and some conditions require site-specific response analysis instead of tabulated factors. GeoEQ Seismic reports Vs30 as a computed value of the profile.

What input ground motions does site response analysis use?

Acceleration time histories, such as PEER NGA records in .AT2 format, declared as rock outcrop or within motion and often scaled or matched to a target spectrum. The declaration matters because outcrop motion is applied at an elastic half-space and within motion at a rigid base.

What does a site response analysis output?

It outputs a surface acceleration time history, response spectra, amplification between input and surface, and depth profiles of peak acceleration, shear strain and shear stress. The first release of GeoEQ Seismic is planned around these outputs.

What analysis types does GeoEQ Seismic cover?

GeoEQ Seismic is in development for one- and two-dimensional seismic site response of layered ground. One-dimensional equivalent-linear analysis is the focus of the first release, and two-dimensional analysis is in development.

Is GeoEQ Seismic available now?

No. GeoEQ Seismic is in development and has not been released. Choose Get notified on the download page and you will be told when it is released.

Which programs are commonly used for 1D site response?

Commonly used programs include DEEPSOIL, Strata, SHAKE91 and SHAKE2000, ProShake, EERA, RSSeismic and SeismoSoil. Each has its own scope, so compare methods and documentation against the needs of the project.

Does 1D site response give 2D results?

No. Several 1D columns along a section give 1D results at each location, but they cannot represent waves travelling sideways, basin-edge effects or topographic scattering. Those effects need a two-dimensional model.

Sources

References

  • Bard, P.-Y., & Bouchon, M. (1980). The seismic response of sediment-filled valleys. Part 1: the case of incident SH waves. Bulletin of the Seismological Society of America, 70(4), 1263-1286.
  • Darendeli, M. B. (2001). Development of a new family of normalized modulus reduction and material damping curves (PhD dissertation). University of Texas at Austin.
  • Hashash, Y. M. A., et al. DEEPSOIL user manual and tutorial. University of Illinois at Urbana-Champaign.
  • Idriss, I. M., & Sun, J. I. (1992). SHAKE91: a computer program for conducting equivalent linear seismic response analyses of horizontally layered soil deposits. University of California, Davis.
  • Kim, B., Hashash, Y. M. A., Stewart, J. P., Rathje, E. M., Harmon, J. A., Musgrove, M. I., Campbell, K. W., & Silva, W. J. (2016). Relative differences between nonlinear and equivalent-linear 1-D site response analyses. Earthquake Spectra, 32(3), 1845-1865.
  • Kottke, A. R., & Rathje, E. M. (2008). Technical manual for Strata (PEER Report 2008/10). Pacific Earthquake Engineering Research Center.
  • Kramer, S. L. (1996). Geotechnical earthquake engineering. Prentice Hall.
  • Kwok, A. O. L., Stewart, J. P., Hashash, Y. M. A., et al. (2007). Use of exact solutions of wave propagation problems to guide implementation of nonlinear seismic ground response analysis procedures. Journal of Geotechnical and Geoenvironmental Engineering, 133(11), 1385-1398.
  • Schnabel, P. B., Lysmer, J., & Seed, H. B. (1972). SHAKE: a computer program for earthquake response analysis of horizontally layered sites (Report EERC 72-12). University of California, Berkeley.

Ground motion records for input are available from the PEER NGA-West2 database. More geotechnical notes are on the GeoEQ blog, and the lab's approach is described on About GeoEQ.

GeoEQ Seismic · In development

Hear when it is ready.

Register your interest and you will be told when GeoEQ Seismic is released. The roadmap shows what is being worked on across the lab.

Today GeoEQ SPT Logs is available: see the borehole log software