Solutions · Shallow foundation design
Shallow foundation design from site investigation data
From SPT and laboratory results to a bearing capacity check, a settlement check and a report.
The short answer
Data first, then two checks.
Shallow foundation design turns site investigation data (SPT blow counts, strata, groundwater and laboratory results) into design soil parameters, then checks that the footing will not fail in bearing and will not settle more than the structure can tolerate.
This page walks the workflow step by step and says plainly which steps GeoEQ tools cover, which are not released yet, and which stay in your own tools.
The workflow
From borehole to footing size, in eight steps.
Each step shows the GeoEQ tool that fits it and that tool's real status. Where a step is marked outside GeoEQ, it happens in your own tools.
- Step 01
Investigate the site
Drill boreholes, run SPT at intervals, take samples and record groundwater. The field record is the foundation of every later number.
Outside GeoEQ: done on site by the drilling crew and field engineer.
- Step 02
Log the boreholes
Turn field sheets into strata, SPT values, samples and groundwater levels on a finished log sheet, one soil profile per borehole.
- Step 03
Classify and test samples
Grain size, Atterberg limits and USCS or AASHTO classification confirm what the field description suggested.
- Step 04
Derive design parameters
Correct SPT values (N60, then N1(60)), apply correlations, reduce shear and consolidation tests, and choose a design value per layer. Choosing the value is a judgement for the engineer.
- Step 05
Set loads and criteria
Column and wall loads, load combinations, factors of safety or partial factors, and tolerable settlement come from the structural engineer and the governing code.
Outside GeoEQ: done in your own tools and with the structural engineer.
- Step 06
Check bearing capacity
Compare the footing pressure with the capacity of the ground, ultimate or allowable, for the size and embedment you are trying.
- Step 07
Check settlement
Estimate immediate and long-term settlement under working load, and differential settlement between footings.
- Step 08
Size, iterate and report
Adjust the footing until both checks pass, then document the logs, parameters, calculations and recommendations in the geotechnical report.
Outside GeoEQ: writing the report and signing it off stay with the engineer.
Only GeoEQ SPT Logs and the geoeq library for Python are available today. GeoEQ Cap is releasing soon and GeoEQ Lab is in development, so for those steps the tools shown are the direction, not something you can use yet. SPT Logs records and presents the field data; it does not do the design calculations.
Explainer
What shallow foundation design involves.
A shallow foundation is checked twice: for bearing capacity, so the ground does not fail in shear, and for settlement, so the structure is not damaged by movement. The first is a strength (ultimate limit state) check; the second is a serviceability check, often held to around 25 mm for footings on granular soil unless the structure needs less.
Bearing capacity is commonly written in terms of the soil's cohesion and friction angle, the unit weight, the footing width and the embedment depth, then reduced by a factor of safety to an allowable pressure. Settlement is estimated as immediate (elastic) movement plus, in clays, consolidation over time. For sands, empirical methods work directly from corrected SPT values. These are background methods; the governing code or textbook you follow decides which one applies to your project.
Inputs
- Borehole logs: strata, SPT values, groundwater depth
- Index and classification results from the laboratory
- Strength and compressibility parameters per layer
- Foundation loads, geometry and embedment depth
- Factors of safety or partial factors and tolerable settlement
Outputs
- Design soil profile with a parameter set per layer
- Bearing capacity result for each trial footing
- Settlement and differential settlement estimates
- Recommended footing size, depth and allowable pressure
- A report that shows the data and every step so it can be checked
Common pitfalls
Where footing designs go wrong.
- Using raw SPT values
- Field N must be corrected for hammer energy, borehole, sampler and rod length before it is used in correlations. See the article on SPT N-value corrections.
- Checking bearing capacity only
- On granular soil, the allowable pressure is often governed by settlement, not by shear failure. Both checks are needed.
- Ignoring the influence zone
- A footing stresses the ground to a depth of roughly one to two widths below it. The profile that matters includes the layers under the footing, not only the founding layer.
- Trusting one borehole
- Variable ground needs a cautious design value across the footprint, and a weak layer between boreholes can govern.
- Treating groundwater as fixed
- A rise in the water table reduces effective stress and capacity. Record the level at the time of drilling and consider its seasonal range.
- Mixing method constants
- Empirical SPT-based pressures differ by reference and by the correction used. Take the method from the governing code or text, and check it matches your corrected N.
Related reading: SPT N-value corrections: N60 and N1(60) explained and Reading the plasticity chart.
Tools for this work
GeoEQ tools for the foundation workflow.
- Releasing soon
GeoEQ Cap
Bearing capacity
Bearing capacity and settlement of shallow foundations.
- Available
GeoEQ SPT Logs
Borehole and boring log software · soil to rock
Log boreholes from soil to rock and export finished log sheets.
- Available
geoeq for Python
Open-source library
170+ geotechnical functions, and the engine behind the desktop programs.
- In development
GeoEQ Lab
Soil laboratory testing
Grain size, Atterberg limits and USCS and AASHTO classification.
Browse the full software catalogue, see the applications GeoEQ covers, or go back to all solutions.
Direct answers
Questions about shallow foundation design.
What is shallow foundation design?
Shallow foundation design is choosing the type, size and depth of footings or mats that sit near the surface, and checking that the ground can carry the load safely and with acceptable settlement. It starts from site investigation data and ends in a geotechnical report.
What site investigation data do you need for a footing design?
You need borehole logs with strata, SPT values and groundwater depth, plus laboratory classification and, for cohesive soils, strength and consolidation results. You also need the loads, footing geometry, embedment depth and the settlement the structure can tolerate.
How do you design a footing from SPT data?
Correct the field N values to N60 and N1(60), average them over the zone the footing stresses, then use an SPT-based or correlated-parameter method from your governing code or text to check bearing capacity and settlement. The method and its constants vary by reference, so follow the one you are required to use.
What are the two main checks in shallow foundation design?
They are bearing capacity, which guards against shear failure of the ground, and settlement, which keeps movement within what the structure tolerates. Differential settlement between footings is checked as part of the settlement check.
Does bearing capacity or settlement usually govern?
On sand and other granular soil, settlement usually governs the allowable pressure unless the soil is loose or the footing is narrow. On soft clay, bearing capacity and consolidation settlement can both control, so check both.
Which steps in this workflow does GeoEQ cover today?
Today GeoEQ SPT Logs covers borehole logging, and the open-source geoeq library for Python covers SPT corrections, correlations, bearing capacity and settlement calculations. GeoEQ Cap and GeoEQ Lab are not released yet, and loads, code criteria and report writing stay in your own tools.
Can I script a foundation calculation now?
Yes. The open-source geoeq library for Python includes bearing capacity and settlement functions and can be installed with pip install geoeq. Documentation is at docs.geoeq.org.
Is GeoEQ Cap available?
Not yet. GeoEQ Cap, for bearing capacity and settlement of shallow foundations, is releasing soon, and GeoEQ Lab is in development. Choose Get notified on the product page and you will be told when each is released.
Shallow foundation design
Start with a clean borehole log.
GeoEQ SPT Logs is free to download. Get notified when GeoEQ Cap is released.