Skip to content
GeoEQ · Geotechnical software research lab · University of Utah

Solutions · For consultants

Software for geotechnical consultants

One soil profile from the borehole log to the report, with an honest view of which steps GeoEQ covers today.

The short answer

From field data to the report, without re-keying.

Software for geotechnical consultants has to carry one soil profile from the borehole log through laboratory results and analysis to the report, and GeoEQ covers that path with GeoEQ SPT Logs available now and Lab, Liq and Cap on the way.

Only GeoEQ SPT Logs is available today. The other tools below are marked with their real status, and the steps GeoEQ does not cover are named as such.

The workflow

A geotechnical investigation, step by step.

Each step is mapped to the GeoEQ tool that covers it, with that tool’s current status. A step marked “your own tools” is not covered by GeoEQ.

  1. 01

    Plan the investigation and drill

    Choose borehole locations and depths, set the testing scope, brief the drilling contractor and supervise the fieldwork. This is judgement and coordination, done in your own tools.

    Your own tools
  2. 02

    Turn field data into borehole logs

    SPT blow counts, strata with USCS symbols, samples, groundwater and rock core runs are logged and drawn to your letterhead, then exported as PDF. Existing Excel or CSV sheets can be imported with column mapping.

    GeoEQ SPT Logs
    Available
  3. 03

    Test the samples and classify the soil

    Grain size, Atterberg limits and USCS and AASHTO classification, with results planned to flow back into the borehole logs. Until it is released, laboratory reduction stays in your lab’s existing tools.

    GeoEQ Lab
    In development
  4. 04

    Check liquefaction and seismic hazard

    Liquefaction triggering from SPT and CPT data, prepared for the report. Seismic design inputs and site-class decisions remain the engineer’s own work, in your own tools. Liquefaction triggering can already be scripted with the open-source geoeq library.

    GeoEQ Liq
    Releasing soon
  5. 05

    Design and check shallow foundations

    Bearing capacity and settlement of shallow foundations computed from the logged soil profile, with every intermediate value shown for the engineer who signs. Piles and structural design are outside GeoEQ.

    GeoEQ Cap
    Releasing soon
  6. 06

    Write and sign the report

    Recommendations, figures, site description and the engineer’s judgement are written in your own tools. GeoEQ supplies the logs and, as the products release, the calculation output that goes into the report.

    Your own tools

What the work involves

Why one soil profile matters.

A geotechnical report rests on a soil profile: layers, their descriptions and classification, penetration resistance and the groundwater level. The profile is first written down as a borehole log. It is then reused in laboratory summaries, in liquefaction screening, in bearing capacity and settlement checks, and finally in the report text.

In many offices the profile is retyped at each stage, so the log, the spreadsheet and the calculation can drift apart. The GeoEQ approach is to log the boreholes once in GeoEQ SPT Logs and have the later tools read the same profile as they are released.

Field SPT values are not used directly by analysis methods. They are corrected to N60 and N1(60) first, which is explained in SPT N-value corrections. For classification and the plasticity chart, see reading the plasticity chart.

Key outputs of the work

  • Borehole logs with strata, SPT N values, samples, groundwater and rock core recovery, drawn to your letterhead
  • Soil classification and index test results to attach to the logs
  • Liquefaction assessment and shallow foundation capacity and settlement, with checkable working
  • The calculation record and figures that support the recommendations in the report

Common pitfalls

  • Re-keying the same data. The same depths and blow counts get typed into a log, a spreadsheet and a calculation. Every re-key is a chance for a transcription error that no one sees until review.
  • Logs that do not match the calculation. If the soil profile in a bearing capacity or liquefaction check is not the one on the log, a late change to a layer silently breaks the report. One soil profile used end to end avoids this.
  • Uncorrected SPT values. Field N values are not what analysis methods consume. Hammer, borehole, sampler and rod corrections give N60, and the overburden factor gives N1(60). See SPT N-value corrections.
  • Calculations no reviewer can follow. A single result with no intermediate values is hard to check. Reviewers and the engineer who signs need to see each step.
  • Mixed units and conventions. Depths in metres on the log and feet in the calculation, or a different group symbol in the lab sheet and the log, are common causes of rework.

Tools for this work

The GeoEQ tools for a consultancy.

Direct answers

Questions from geotechnical consultants.

More: applications covered, all software and all solutions.

What software do geotechnical consultants need?

Consultants need software for borehole logging, laboratory result reduction, analysis such as liquefaction and shallow foundation design, and a way to carry one soil profile into the report. GeoEQ covers logging today with SPT Logs and is building the laboratory, liquefaction and bearing capacity steps.

What can GeoEQ do for a geotechnical consultancy today?

GeoEQ SPT Logs is available now: it turns SPT field data, strata, samples, groundwater and rock cores into finished borehole logs and a PDF for the whole site. The open-source geoeq library for Python is also available for scripted calculations, including liquefaction triggering.

Which GeoEQ tools are not released yet?

GeoEQ Cap (shallow foundations) and GeoEQ Liq (liquefaction) are releasing soon. GeoEQ Lab (soil laboratory testing) is in development. Choose Get notified on a product page and you will be told when it is released.

Is GeoEQ a replacement for my whole geotechnical software stack?

No. GeoEQ covers logging, soil laboratory testing, liquefaction and shallow foundation calculations. Piles, slope stability, retaining walls, finite element modelling and report writing are done in your own tools.

Can I bring my existing Excel borehole data into the workflow?

Yes. GeoEQ SPT Logs imports Excel and CSV files with any column headings. A mapping dialog lets you assign columns before any row enters the project, so office templates keep working.

Do I need to be online to use GeoEQ SPT Logs?

No. It is a Windows 10 and 11 desktop program that runs offline, and projects are saved as plain files on your computer.

What is the typical workflow from borehole to geotechnical report?

Plan and drill the investigation, log the boreholes, test the samples, correct the SPT values, run the analyses such as liquefaction and foundation checks, then write and sign the report. The GeoEQ steps share one soil profile so it is entered once.

Can I reproduce GeoEQ calculations independently?

Yes. The same engine used inside GeoEQ software is published as the open-source geoeq library for Python (pip install geoeq), so a calculation can be reproduced in a script and checked.

GeoEQ · For consultants

Start with the borehole logs.

GeoEQ SPT Logs is available now. Choose Get notified on the other products and you will be told when each is released.