Skip to content
GeoEQ · Geotechnical software research lab · University of Utah

Glossary

Geotechnical engineering glossary: the terms behind the borehole log

Short, standards-referenced definitions of the terms used in site investigation, laboratory testing, foundation design, liquefaction and seismic analysis and granular modelling.

Category

Site investigation

Boring log

Also: borehole log · bore log · borelog

A record of the soil and rock encountered in a borehole during drilling, including strata, samples, groundwater and in-situ test results. “Boring log” is the usual term in the United States and “borehole log” in the UK, Europe and Australia; no formal distinction between them was found.

Standard Penetration Test (SPT)

Also: SPT · SPT N-value · blow count

An in-situ test in which a 63.5 kg hammer falling 760 mm drives a split-barrel sampler 450 mm in three 150 mm increments (ASTM D1586). The N-value is the number of blows for the second and third increments; the first is a seating drive. Refusal is reported with the penetration reached, for example 50/125 mm.

Hammer energy ratio

Also: ER · CE · energy correction

The energy actually delivered to the SPT drill rods divided by the theoretical energy of the hammer drop, about 475 J, expressed as a percentage and measured as described in ASTM D4633. The energy correction is CE = ER / 60, so a rig with a measured ER of 55% has CE of about 0.92.

N60

Also: energy-corrected N-value

The SPT blow count corrected to 60% hammer energy: N60 = N × CE × CB × CR × CS, where the factors account for hammer energy, borehole diameter, rod length and sampler type. It removes equipment effects so blow counts from different rigs can be compared.

Overburden correction (CN)

Also: CN · effective stress normalisation

A factor that normalises an SPT result to a reference effective vertical stress of one atmosphere (about 100 kPa) so tests at different depths can be compared. A common form is CN = (Pa / σ′v)^0.5, capped at 1.7; it applies to granular soils, not clays.

N1(60)

Also: (N1)60 · overburden-normalised N-value

N60 further corrected for effective overburden stress: N1(60) = N60 × CN. It is the value used for relative density estimates in sands and as the input to SPT-based liquefaction triggering procedures.

Cone Penetration Test (CPT)

Also: CPT · CPTu · piezocone

An in-situ test in which an instrumented cone is pushed into the ground at a constant rate, about 20 mm/s, recording tip resistance, sleeve friction and, for CPTu, pore pressure (ASTM D5778). It gives a near-continuous profile and is widely used for stratigraphy and liquefaction assessment.

Rock Quality Designation (RQD)

Also: RQD

The combined length of sound core pieces 100 mm (4 in) or longer, divided by the length of the core run, expressed as a percentage (Deere, 1964; ASTM D6032). It is a simple index of fracturing and is reported alongside core recovery.

Total core recovery (TCR)

Also: TCR · core recovery

The length of core recovered from a run, including broken pieces, divided by the run length, as a percentage. For the same run it is never smaller than the solid core recovery or the RQD.

Solid core recovery (SCR)

Also: SCR

The length of full-diameter solid core cylinders recovered from a run, divided by the run length, as a percentage. Unlike RQD it does not require a minimum piece length.

Category

Laboratory

Grain size distribution

Also: particle size distribution · gradation · sieve analysis

The percentage of a soil, by dry mass, finer than each particle size, plotted as a grading curve against a logarithmic size axis. The sieve part is run to ASTM D6913 and the sedimentation part to ASTM D7928.

Hydrometer analysis

Also: sedimentation analysis

A sedimentation test that finds the particle size distribution of the material finer than the 0.075 mm (No. 200) sieve from the changing density of a soil suspension (ASTM D7928).

Coefficient of uniformity and curvature (Cu, Cc)

Also: Cu · Cc · D10 · D60

Cu = D60 / D10 and Cc = D30² / (D10 × D60), where Dn is the diameter at which n percent of the sample by dry mass is finer. In ASTM D2487 a well-graded gravel needs Cu of at least 4 and a well-graded sand Cu of at least 6, each with Cc from 1 to 3.

Atterberg limits

Also: consistency limits

The water contents at which a fine-grained soil changes between liquid, plastic and semisolid behaviour, chiefly the liquid limit and the plastic limit, measured on the fraction passing the 0.425 mm (No. 40) sieve (ASTM D4318).

Liquid limit (LL)

Also: LL

The water content, in percent, at which a soil passes from plastic to liquid behaviour, read from the flow curve at 25 blows and reported as a whole number (ASTM D4318; AASHTO T 89).

Plastic limit (PL)

Also: PL

The water content, in percent, at which a soil passes from semisolid to plastic behaviour, found by rolling threads of soil to 3.2 mm diameter until they crumble (ASTM D4318).

Plasticity index (PI)

Also: PI

Liquid limit minus plastic limit, in percentage points: PI = LL − PL. It is the range of water content over which the soil is plastic, and the vertical axis of the plasticity chart.

A-line and U-line

Also: plasticity chart · Casagrande chart

On the plasticity chart the A-line, PI = 0.73 (LL − 20), separates clays (above) from silts and organic soils (below). The U-line, PI = 0.9 (LL − 8), is an empirical upper bound, and a result plotting above it usually points to a testing or reporting error (ASTM D2487).

Unified Soil Classification System (USCS)

Also: USCS · ASTM D2487

A soil classification system in ASTM D2487 that assigns a group symbol such as SW, SM, CL or CH from grain size distribution and Atterberg limits. A soil is fine-grained when more than 50% passes the 0.075 mm sieve; dual symbols such as CL-ML are used where the data do not support a single group.

AASHTO soil classification

Also: AASHTO M 145 · A-1 to A-7 · group index

A highway-oriented classification (AASHTO M 145) that places a soil in groups A-1 to A-7 using the percentage passing the 0.075 mm sieve, liquid limit and plasticity index. Soils with 35% or less passing are granular; those with more than 35% are silt-clay materials. A group index may be added.

Category

Foundations

Ultimate bearing capacity

Also: qu · qult

The contact pressure at which the soil beneath a foundation fails in shear. In the general form, a cohesion term c·Nc, a surcharge term q·Nq and a self-weight term 0.5·γ·B·Nγ are added, each with shape, depth and inclination factors.

Bearing capacity factors (Nc, Nq, Nγ)

Also: Nc · Nq · Nγ

Dimensionless factors that depend only on the soil friction angle φ. Nq = e^(π tan φ) tan²(45° + φ/2) and Nc = (Nq − 1) cot φ are common to the standard methods, while Nγ is defined differently by Meyerhof, Hansen and Vesic, so results differ between methods.

Depth factors (dc, dq, dγ)

Also: dc · dq · dγ

Multipliers in the bearing capacity equation that account for the shear strength of the soil above the foundation base, increasing capacity with embedment depth Df relative to width B. Their form depends on the method (Meyerhof, Hansen, Vesic).

Allowable bearing capacity and factor of safety

Also: qa · FS · safe bearing capacity

The ultimate bearing capacity divided by a factor of safety, q_a = q_u / FS, with FS commonly taken as 3 for static loads unless the governing code sets another value. The allowable value may also be limited by the settlement the structure can tolerate.

Category

Liquefaction & seismic

Soil liquefaction

Also: cyclic liquefaction

The loss of strength and stiffness of saturated, loose, mostly cohesionless soil when cyclic loading from an earthquake raises pore water pressure toward the effective overburden stress. Triggering is usually screened with SPT or CPT based procedures such as Youd and Idriss (2001) or Boulanger and Idriss (2014).

Cyclic stress ratio (CSR)

Also: CSR

The seismic shear stress demand on a soil layer as a fraction of the effective vertical stress. The simplified form is CSR = 0.65 (amax / g) (σv / σ′v) rd, where rd is a depth-dependent stress reduction coefficient.

Cyclic resistance ratio (CRR)

Also: CRR · CRR7.5

The cyclic stress ratio a soil layer can resist before liquefying, obtained from corrected SPT or CPT resistance and normalised to a magnitude 7.5 earthquake. A magnitude scaling factor adjusts it for other magnitudes.

Factor of safety against liquefaction

Also: FSL

The ratio of cyclic resistance to cyclic stress, FS = CRR / CSR, with magnitude scaling applied where the procedure requires it. Values below 1.0 indicate that liquefaction is predicted for that layer.

Fines content correction

Also: clean-sand equivalent · N1(60)cs

An adjustment that converts N1(60) to an equivalent clean-sand value, N1(60)cs, using the percentage of fines passing the 0.075 mm sieve, because silty sands show higher resistance for the same blow count. It is applied inside liquefaction triggering procedures, not to N60 or N1(60) themselves.

Vs30

Also: time-averaged shear-wave velocity

The time-averaged shear-wave velocity of the upper 30 m of a profile, equal to 30 m divided by the total shear-wave travel time through those 30 m. It is the main parameter for site classification in building codes.

Site class

Also: ASCE 7 site class · soil profile type

A code category, A to F in ASCE 7 (ASCE 7-22 adds the intermediate classes BC, CD and DE), describing the stiffness of the upper 30 m of the profile, based on Vs30 or, where that is not measured, on N60 or undrained shear strength. It sets site coefficients for design ground motion, and Site Class F requires a site-specific response analysis.

Site response analysis

Also: ground response analysis · seismic site response

A calculation of how the soil and rock layers beneath a site modify earthquake ground motion between bedrock and the ground surface. One-dimensional methods are linear, equivalent-linear or nonlinear; equivalent-linear analysis repeats a frequency-domain calculation with modulus and damping updated to be compatible with the computed shear strain.

Category

Granular modelling

Discrete element method (DEM)

Also: DEM · distinct element method · discrete element modelling

A numerical method that models a granular material as a collection of individual particles, calculating contact forces between them and integrating the equations of motion in time (Cundall and Strack, 1979). It is used to study soil behaviour at the particle scale.

Coordination number

Also: average contact number

The average number of contacts per particle in an assembly, 2Nc / Np for Nc contacts among Np particles. It is a basic measure of packing and of how well an assembly can carry load.

Contact model

Also: contact law · force-displacement law

The rule that converts the overlap and relative motion of two particles into normal and tangential contact forces in a discrete element simulation, such as a linear spring-dashpot or a Hertz-Mindlin model, with a friction limit on the tangential force.

Get started

Start with the one that is already free.

GeoEQ SPT Logs runs on Windows from a signed installer. A free account is needed to download; the software itself runs offline with no sign-in, no licence key and no expiry.