Solutions · Soil laboratory testing
Soil classification from lab tests: the laboratory workflow, step by step
From the sample that arrives at the lab to the group symbol on the borehole log: what each step involves and which GeoEQ tool covers it.
The short answer
Grain size, then limits, then a group symbol.
Soil is classified from lab tests by reducing a grain size analysis to the percentage passing the 0.075 mm sieve, running Atterberg limits on the fine fraction, and then applying the USCS (ASTM D2487) or AASHTO (M 145) rules to give a group symbol that goes back into the borehole log.
This page follows that workflow and is honest about coverage. GeoEQ SPT Logs and the open-source geoeq library are available now. GeoEQ Lab, which covers the reduction and classification steps, is in development. Physical testing is done in your laboratory.
The workflow
Seven steps from sample to reported result.
Each step shows the GeoEQ tool that covers it and that tool's real status. Where no tool is shown, the step is done in your own tools.
- Step 01
Receive samples and match them to the field log
Each sample arrives with a borehole, depth and type (disturbed or undisturbed), and has to be matched to the log it came from before anything is tested.
- GeoEQ SPT Logs Available
The field side: the disturbed and undisturbed samples recorded on the borehole log.
Outside GeoEQReceipt, labelling, storage and tracking of the physical samples are done in your own laboratory records.
-
- Step 02
Prepare specimens and run the bench tests
Specimens are washed, dried or kept moist as the method requires, then sieved, put through hydrometer sedimentation, or tested for liquid and plastic limit.
Outside GeoEQThe physical testing is done on the bench with your own equipment and methods. GeoEQ does not run or record the apparatus.
- Step 03
Reduce the grain size data
Retained masses become percent passing, the sieve and hydrometer results are joined into one curve, and D10, D30, D60, Cu, Cc and the gravel, sand, silt and clay fractions are read from it.
- GeoEQ Lab In development
Grain size distribution.
-
- Step 04
Reduce the Atterberg limits
The liquid limit comes from the flow curve at 25 blows, the plastic limit from the trial water contents, and the plasticity index is the difference. The point is then plotted on the plasticity chart.
- GeoEQ Lab In development
Atterberg limits.
-
- Step 05
Classify the soil
Grain size and plasticity are combined into a USCS group symbol and an AASHTO group, so the description on the log matches the test results.
- GeoEQ Lab In development
USCS and AASHTO classification.
- geoeq for Python Available
Classification and grain size functions you can call in a script to check or batch-run results.
-
- Step 06
Check the results and report them back to the logs
The engineer reviews the numbers against the visual description, then the fines content, limits and classification are placed against the right sample on each borehole log.
- GeoEQ Lab In development
Results are planned to flow into GeoEQ SPT Logs borehole logs. This link is part of the Lab scope in development.
- GeoEQ SPT Logs Available
The borehole log sheets and PDF the results are reported on.
Outside GeoEQThe engineer reviews and signs. Software does not replace that check.
-
- Step 07
Other tests and the formal laboratory report
Moisture content, strength, consolidation and similar tests, and the signed test certificates a client expects, sit beside the classification tests.
- geoeq for Python Available
Reduction of further laboratory tests can be scripted with the open-source library.
Outside GeoEQOther test reports and certificates are produced in your own tools. GeoEQ Lab is scoped to grain size, Atterberg limits and classification.
-
What the task involves
Three calculations decide the symbol.
The standards named here describe the tests themselves. Check thresholds against the edition your project specifies. Naming a standard on this page is not a claim that any GeoEQ tool conforms to it.
Grain size
Sieve analysis covers the coarse fraction down to 0.075 mm (ASTM D6913). Sedimentation with a hydrometer covers the fines (ASTM D7928). The curve gives D10, D30 and D60, from which the coefficient of uniformity Cu = D60 / D10 and the coefficient of curvature Cc = D30² / (D10 × D60) follow.
Atterberg limits
Liquid limit, plastic limit and plasticity index are measured on the material passing the 0.425 mm (No. 40) sieve (ASTM D4318). PI = LL − PL. On the plasticity chart the A-line, PI = 0.73 (LL − 20), separates clays above from silts below. See the note on reading the plasticity chart.
Classification
USCS (ASTM D2487): fine-grained when 50 percent or more passes 0.075 mm, and plotted on the plasticity chart. Otherwise coarse, split into gravel and sand at 4.75 mm, with gradation and fines deciding symbols such as GW, SP or SC, and dual symbols at 5 to 12 percent fines. AASHTO (M 145) uses a 35 percent threshold and a group index.
Related reading: Reading the plasticity chart explains the A-line, the U-line and the CL-ML zone.
Key outputs
- Grain size curve with D10, D30, D60, Cu and Cc
- Percentages of gravel, sand, silt and clay
- Liquid limit, plastic limit and plasticity index, and the plasticity chart point
- USCS group symbol and AASHTO group for each sample
- Results placed against the sample on the borehole log
Common pitfalls
- An unrepresentative sample
- A classification describes the specimen, not the stratum. If the tested material is not representative of the layer, the symbol on the log is wrong however carefully it was computed.
- Specimen preparation changes plasticity
- Some soils change their limits when they are dried before testing. Follow the preparation the method calls for and record it.
- A flow curve with too narrow a range
- A liquid limit read at 25 blows from points that all sit well above or below 25 is an extrapolation. Aim for trials that bracket 25 blows.
- Fines content from the wrong test
- If a hydrometer is run, the percentage passing 0.075 mm has to agree with the sieve result before it is used to decide coarse or fine.
- Mixing USCS and AASHTO thresholds
- USCS splits coarse and fine at 50 percent passing 0.075 mm. AASHTO uses 35 percent. A soil can legitimately fall in two different groups.
- Results attached to the wrong depth
- A correct result against the wrong sample ID is worse than no result. Check borehole, depth and sample number when results go back to the log.
Tools for this work
GeoEQ software for the laboratory workflow.
- In development
GeoEQ Lab
Soil laboratory testing
Grain size, Atterberg limits and USCS and AASHTO classification.
- Available
GeoEQ SPT Logs
Borehole and boring log software · soil to rock
Log boreholes from soil to rock and export finished log sheets.
- Available
geoeq for Python
Open-source library
170+ geotechnical functions, and the engine behind the desktop programs.
Explore more
See every GeoEQ product, the applications they cover, or the full set of solutions. Related: site investigation and soil laboratories.
Direct answers
Questions about the soil laboratory workflow.
Answers are kept in visible HTML and structured data so people, search engines and AI systems receive the same answer.
How do you classify soil from lab tests?
Find the percentage passing the 0.075 mm sieve from the grain size test; if it is 50 percent or more the soil is fine-grained and is classified from its liquid limit and plasticity index on the plasticity chart. Otherwise it is coarse, split into gravel or sand and refined by fines content, Cu and Cc (ASTM D2487).
Which lab tests are needed to classify a soil?
A grain size analysis (sieve, with a hydrometer when the fines need to be described) and, for any significant fine fraction, the Atterberg limits. Those two tests give every input USCS and AASHTO need. Moisture content and other tests describe the soil further but do not change the symbol.
What is the workflow from sample to lab report?
Receive and log the samples, prepare specimens, run the bench tests, reduce the grain size and Atterberg data, classify, check the results with the engineer, and report them against the right sample on the borehole logs and in the laboratory report.
How are Cu and Cc calculated?
Cu = D60 / D10 and Cc = D30² / (D10 × D60), with D values read from the grain size curve. A gravel is well graded when Cu is at least 4 and Cc is between 1 and 3; a sand when Cu is at least 6 and Cc is between 1 and 3 (ASTM D2487).
How is the liquid limit found?
Plot water content against the number of blows on a logarithmic scale for three or more trials, fit a straight line, and read the water content at 25 blows (ASTM D4318). The plasticity index is the liquid limit minus the plastic limit.
Why can USCS and AASHTO give different answers?
They split coarse and fine soils at different fines contents, 50 percent passing 0.075 mm for USCS and 35 percent for AASHTO, and they are built for different purposes. The two symbols describe the same soil and can both be correct.
How do lab results get back into the borehole log?
Usually the engineer copies fines content, limits and classification against each sample by hand. GeoEQ Lab is planned to send results into GeoEQ SPT Logs borehole logs; it is in development, so that link is not available yet.
Which steps of this workflow does GeoEQ cover today?
GeoEQ SPT Logs is available now for the borehole log, and the open-source geoeq library for Python has classification and grain size functions. GeoEQ Lab, for grain size, Atterberg limits and USCS and AASHTO classification, is in development. Sample receipt and bench testing are outside GeoEQ.
Soil laboratory testing
From the lab bench back to the log.
Download GeoEQ SPT Logs for the borehole log, or get notified when GeoEQ Lab is released.