Skip to content
GeoEQ · Geotechnical software research lab · University of Utah

Solutions · Seismic hazard

Liquefaction and seismic hazard assessment for a site

The real steps of the task, from SPT and CPT data to triggering, settlement and site response, and the GeoEQ tools that fit each one.

The short answer

What the assessment is.

A liquefaction and seismic hazard assessment for a site compares the earthquake loading on each soil layer with the resistance measured by SPT or CPT, then estimates the consequences (settlement, LPI, LSN) and, where needed, how the ground modifies shaking.

The result is a set of numbers the geotechnical report can defend: a factor of safety against liquefaction by depth, settlement, severity indices and, where the project needs it, a view of how the ground modifies shaking.

The workflow

Seven steps, and who does each one.

Each step shows the GeoEQ tool that covers it and that tool’s real status. Steps GeoEQ does not cover are marked as outside GeoEQ.

  1. 01

    Screen the site and set the earthquake

    Review geology, mapped hazard zones, groundwater and prior reports to decide whether liquefaction is plausible. The design peak ground acceleration and magnitude normally come from a seismic hazard analysis or a design code.

    Outside GeoEQ: done in your own tools and from the governing code or hazard study.

  2. 02

    Investigate: SPT boreholes and CPT soundings

    Drill and log boreholes with SPT blow counts, strata, samples and groundwater. CPT soundings are run by the CPT contractor.

    GeoEQ SPT Logs Available

    SPT Logs covers the borehole log. CPT soundings are recorded by the CPT contractor, outside GeoEQ.

  3. 03

    Test fines content and plasticity

    Grain size and Atterberg limits on samples give the fines content and plasticity that triggering and susceptibility screening need.

    Outside GeoEQ today: done in your laboratory or your own tools.

  4. 04

    Evaluate liquefaction triggering

    Screen layers for susceptibility, calculate the cyclic stress ratio and cyclic resistance ratio, and report a factor of safety at each depth.

    GeoEQ Liq Releasing soon

    Available today: the open-source geoeq library for Python includes liquefaction triggering.

  5. 05

    Estimate the consequences

    Volumetric strain and free-field settlement, and the profile indices LPI and LSN with severity classes. Lateral spreading, slope stability and effects on structures are assessed separately.

    GeoEQ Liq Releasing soon

    Lateral spreading, slope stability and structural effects: outside GeoEQ.

  6. 06

    Assess site response where it is needed

    Where the ground may amplify or reshape shaking, one- and two-dimensional site response analysis studies the layered profile.

    GeoEQ Seismic In development
  7. 07

    Report and recommend

    Assemble the results, the basis of the design motion and the recommendations, including any mitigation, in the geotechnical report the engineer signs.

    GeoEQ Liq Releasing soon

    Liq prepares the results sheets for the report; the report and recommendations remain the engineer’s.

What it involves

Triggering, consequences, site response.

Triggering compares demand with capacity. The cyclic stress ratio (CSR) comes from the design peak ground acceleration, the stress state and a depth reduction factor. The cyclic resistance ratio (CRR) comes from corrected SPT or CPT resistance, adjusted for fines, magnitude and overburden. FS = CRR / CSR below 1.0 indicates liquefaction. Fine-grained layers are screened for susceptibility first.

Consequences turn a triggering result into something a structure feels: volumetric strain and free-field settlement, and indices that summarise the profile. LPI indicates how likely surface manifestation is; LSN indicates how severe the damage may be.

Site response studies how layered ground changes earthquake motion on its way up, which can change the shaking that other checks use.

Related: SPT N-value corrections: N60 and N1(60) explained.

What the assessment produces

  • Factor of safety against liquefaction at each depth
  • Which layers are susceptible, and which were screened out and why
  • Volumetric strain and free-field settlement
  • LPI and LSN for each borehole or sounding, with severity classes
  • Where applicable, how layered ground changes shaking at the surface

Common pitfalls

Where assessments go wrong.

Using uncorrected blow counts

Triggering charts use N60, then (N1)60 and (N1)60cs. Skipping the hammer, rod, borehole and overburden corrections shifts every result.

Wrong groundwater depth

Only saturated layers are evaluated, and the water table sets effective stress. Use a design groundwater level and check the sensitivity to it.

Fines and plasticity assumed

The fines adjustment and the susceptibility screen need measured fines content and plasticity. Estimated values should be flagged as estimates.

Thin layers and transition zones

Thin sand lenses and soil-type transitions are easy to miss or misclassify in a CPT trace; boreholes help identify them.

Stretching the simplified procedure

The simplified procedure was developed for shallow soils under level to gently sloping ground. Steep ground, deep layers or free faces call for justification or other methods.

Treating site response and triggering as one step

Triggering from a design peak ground acceleration and a site response study answer different questions. State which motion you used and why.

Tools for this work

GeoEQ tools for the assessment.

Only GeoEQ SPT Logs is available to download. GeoEQ Liq is releasing soon and GeoEQ Seismic is in development; choose Get notified to hear when they are released.

Browse all GeoEQ software, the applications GeoEQ covers, or the Solutions hub.

Direct answers

Questions about liquefaction and seismic hazard assessment.

What is a liquefaction assessment?

A liquefaction assessment is the engineering evaluation of whether saturated soil at a site could lose strength in an earthquake, and what that would do to the ground and structures. It covers susceptibility, triggering, and consequences such as settlement.

What are the steps of a liquefaction and seismic hazard assessment?

Screen the site, investigate with SPT or CPT, test fines and plasticity, evaluate triggering, estimate consequences, add site response where needed, then report. This page maps each step to the GeoEQ tool that covers it, and names the steps that GeoEQ does not.

Should I use SPT or CPT data for liquefaction?

Both are accepted, and many projects use both. CPT gives a continuous record and maps layers well; SPT gives samples for soil identification and fines content. Agency guidance such as Caltrans favours CPT for final evaluations on larger projects and keeps SPT for identification.

What does a factor of safety against liquefaction mean?

It is the cyclic resistance ratio divided by the cyclic stress ratio, FS = CRR / CSR, with CRR adjusted for magnitude and overburden. Values below 1.0 indicate that liquefaction is predicted at that depth.

What do LPI and LSN tell you?

The Liquefaction Potential Index (Iwasaki et al. 1978) condenses a whole profile into one number weighted toward shallow, thick, low-FS layers. The Liquefaction Severity Number (van Ballegooy et al. 2014) weights estimated volumetric strain by depth to indicate expected land damage. Both come with severity classes.

Where does seismic site response fit in?

Site response studies how the soil layers change earthquake motion on its way to the surface. It informs the motion used for design, while triggering decides whether layers liquefy under that motion. They are related but separate analyses.

Which steps does GeoEQ cover today?

Today GeoEQ SPT Logs covers borehole logging, and the open-source geoeq library for Python includes liquefaction triggering. GeoEQ Liq is releasing soon and GeoEQ Seismic is in development. Hazard analysis, CPT acquisition, laboratory work, lateral spreading and mitigation design are outside GeoEQ.

Can I script liquefaction triggering today?

Yes. The open-source geoeq library for Python includes liquefaction triggering and installs with pip install geoeq. Documentation is at docs.geoeq.org.

Liquefaction & seismic hazard

Start with the borehole log.

GeoEQ SPT Logs is available now. GeoEQ Liq and GeoEQ Seismic are not released yet; choose Get notified to hear when they are.